Wrenches&Hammers&Drills&Screwdrivers Wrenches&Hammers&Drills&Screwdrivers.Tool Sets & Riveters & Socket Sets Tool Sets & Riveters & Socket Sets.Tire Air Compressors Tire Air Compressors.Sander Tools Sale - 50% off Sander Tools Sale - 50% off.Recommended for you Recommended for you.Measuring Tools Sale Measuring Tools Sale.Heat Guns & Paint Sprayers Heat Guns & Paint Sprayers.Halloween Sale - 45% off Halloween Sale - 45% off.Halloween Day - test Halloween Day - test.Fire Pit Table Sale Fire Pit Table Sale.Drain Augers & Planers & Angle Grinder Drain Augers & Planers & Angle Grinder.?The Best TACKLIFE Car Jump Starter? ?The Best TACKLIFE Car Jump Starter?.?TACKLIFE Car Tire Inflator ? ?TACKLIFE Car Tire Inflator ?.Marking a large range of graphics, properly divided into several parts to fill, can effectively reduce the jump time and improve the efficiency of marking. When the effect allows, you can increase the “jump speed” of the “advanced” and reduce the “jump delay” For marking thick graphics and fonts, you can remove “enable outline” and “walk once” A, check “Evenly distribute fill lines”.Therefore, suitable processing materials can effectively improve marking efficiency. Processing materialsįor example: good (thick oxide layer, uniform oxidation, no wire drawing treatment, fine sandblasting) anodized aluminum, when the scanning speed reaches two to three thousand millimeters per second, it can also produce very dark effects poor aluminum oxide, scanning speed It can only reach a few hundred millimeters per second. For two-way filling and one-way filling, which often switch lights, it can effectively improve the marking efficiency.Ĭhoosing a laser whose pulse width and pulse frequency are independently adjustable can not only ensure a certain amount of overlap of the focused spot at high scanning speeds, but also ensure that the laser energy has sufficient peak power to reach the destruction threshold of the material and make the material gas化. Choose the right laserįor lasers that can be used for the first pulse, adjust the height of the first pulse, and the light-on delay can be 0. Thin graphics and fonts are greatly affected by the delay, and the delay can be increased appropriately. Remarks: Thick graphics and fonts are less affected by the delay, and the delay can be appropriately reduced. Two-way filling, one-way filling: Mainly affected by the light-on delay and light-off delay, which can reduce the corner delay and end delay. Therefore, reducing the delay irrelevant to the filling type can improve marking efficiency.īow-shaped filling and round-shaped filling: Mainly affected by the corner delay, it can reduce the light on delay, light off delay, and end delay. Set an appropriate delayĭifferent filling types are affected by different delays. In addition, when using ordinary galvanometers to mark small graphics or fonts, deformation is prone to occur, and the scanning speed must be reduced to ensure the effect. Ordinary galvanometer, the maximum scanning speed can only reach two to three thousand millimeters per second high-speed galvanometer, the maximum scanning speed can reach tens of thousands of millimeters per second, effectively increasing the marking efficiency. Therefore, it is necessary to increase the filling line spacing while ensuring sufficient marking energy. Remarks: The larger the field lens, the lower the power density. Under the same spot overlap rate, the filling line spacing can be increased, thereby improving the marking efficiency. The larger the focal length of the field lens, the larger the focused spot. Two-way filling is the best choice to ensure effect and efficiency. Summary: In the case of not requiring detailed effects, the use of bow-shaped filling can improve marking efficiency.Filling: It is only used when marking thin graphics and fonts, and the efficiency is similar to that of bow filling.One-way filling: The marking efficiency is the slowest, and it is rarely used in actual processing.Two-way filling: The marking efficiency is second, and the effect is good.When marking thin graphics and fonts, the above problems will not occur, so bow filling is the first choice. Bow-shaped filling: The marking efficiency is the highest, and sometimes there will be problems with connection lines and unevenness.Measures to improve marking efficiency 1.Select the appropriate filling type Therefore, factors such as filling type, field lens (filling line spacing), galvanometer (scanning speed), delay, laser, processing materials, etc., ultimately affect marking efficiency. From these two factors, it can be subdivided into different aspects: For a fixed marking pattern, the factors that affect the marking efficiency can be divided into the equipment itself and the processing material.